The error codes Hansa washing machines
Video repair Hansa washing machines
Replacement parts in a Hansa washing machines
CM series RA
E01 – Faulty door lock (no locks ) . The washing program is interrupted ( in the absence of lock – 2 seconds . , In case of failure of the limit switch – 10 sec . )
E02 – Faulty water level sensor : no signal on the achievement of Level I water wash stops.
E03 – Faulty drain system : no signal from the sensor on the absence of water. CM blocks hatch fully shutdown the unit.
E04 – working overflow tank in this case CM automatically interrupts the wash and includes a drain pump . Luke remains locked until complete shutdown of the machine.
E05 – A whistleblower in the temperature sensor : the water is heated by less than 40 after 10 minutes of heating element (due to circuit or interruption ) or does not meet the software standards. Washing is continued without heating water.
E07 – The system records in the washing mode is no contact of the control ( electronic controller ) with tachometer . Wash stops.
E08 – The system records in the extraction mode control’s lack of contact with the tachometer . Stop the cycle.
E10 – The system records mismatch mains ( voltage, frequency) . Wash stops.
E11 – fault detected (short circuit) of the control ( triac ) drive motor. Wash stops.
E12 – The system captures water from leaking into the sump CM ( due to sensor signals AQUA STOP). Drain pump is activated , locked the door catch . The door opens after receiving the signal ” empty tank “.
E14 – Malfunction of the electronic controller . Wash stops.
E15 – On power up or after selecting the washing is a fault of the electronic controller .
CM Series PC
E01 – The system indicates the absence of a control signal for the inclusion of a locking door lock
E02 – Signal problems with bulk water ( working time filling the tank to the nominal level exceeded 2 min)
E03 – Signal problems with drainage water ( draining the water from the working tank exceeds 1.5 min)
E04 – Signal problems with bulk water ( pressure switch sends a signal to the working tank overflow )
E05 – Signal problems with bulk water ( working time filling the tank to the specified level over 10 min)
E06 – Signal problems with drainage water ( for 10 minutes of no signal pressotstata “Empty tank “)
E07 – The system captures water from leaking into the sump CM ( due to sensor signals AQUA STOP).
E08 – The system records mismatch mains ( voltage, frequency) .
E09 – Excessive foam in the ” spin “, with which the system could not cope
E11 – The system reports a fault triac ( control element ) food chain locking mechanism hatch
E21 – Failure of the drive motor ( no connection to the tachometer , the blocking of the motor )
E22 – Failure of the drive motor ( unauthorized rotation)
E31 – fault detected the temperature sensor (short circuit)
E32 – fault detected the temperature sensor (open circuit)
E42 – Failure of the locking mechanism
E52 – Faulty battery memory machines
- LG Washing Machine De error code how to replace door interlocks
This video will help you when your washing machine will not start you may have a fault the dE error code indicates that the washer ..
- Automatic Washing Machine Repair | E3 Error Troubleshooting | Latest Way 2020-21
In this video, we described an automatic Washing Machine repairing. E3 error troubleshooting in Washing Machine
- Samsung Washing Machine 3E Error Code not spinning or turning
3E error code is a Motor tacho fault detected Can also be caused by be main PCB If the motor tacho signals are inputted less than ..
- Identifying LG Error Codes and Problems
If your LG washer or washer dryer is showing two letters in the display after stopping it is likely to be a fault code. In this video, Mat …
3:18 So there we have the washing machine error code on LG washing machines. Remember these are a guide and can mislead the …
- Whirlpool Washing Machine Error Codes Diagnosis
If your washing machine does not complete a cycle and the display shows a letter and two digits it is likely to be showing an erro
- Error Codes Of Samsung Front Load Washing Machine | How to Solve Them
If You liked the Video, Kindly Support Us: bijaysingh Paytm, Phone Pe, Google Pay : 9000005315 BUY Quick .
- Samsung washing machine 5E or 2E error code Pump fault not emptying
Pump won’t empty – not draining As usual with these error codes for not draining the first thing to do is check the pump filter but, on ..
- Washing machine starts then stops or turns off
Please remember to mark us to your favourites also I would be grateful if you would subscribe to our channels social media as this ..
- How to Identify Bosch Washing Machine Error Codes
When your Bosch washing machine experiences an issue, it will stop the wash cycle and flash an error code. Find out what the .
- How a washing machine door lock works, how to test interlocks
Washing machine door locks really only get 3 major faults The points between live and common fail in some way. The NTC heater ..